The general cutting process includes the following steps: labeled (threading): This is the first step of diamond cutting, first check the drill blank, and mark it on the surface of the diamond. Experience and proficient processing technology. The ultimate goal is to create the largest, cleanest and most perfect diamonds to reflect the value of diamonds as high as possible. The thorough person must pay attention to two points: that is, try to maintain the maximum weight and minimize the internal content. The threadr uses a magnifying glass to study the structure of the drilling billet. If it is a large particle diamond, this work may take several months, and it takes several minutes to the ordinary drill billet. , no matter how small the drilling billet is small, each diamond must be checked in detail to make the correct judgment. This thoroughly marked with Indian ink on the drill billet, showing that the drill billet should be divided along this line. Usually, as much as possible along the natural texture direction of diamonds.
The segmentation rough: including cutting and sawing cutting.
This chopping: The splitter puts the diamond billet of the schemes on the suitcase, and then cuts a dentan along the segmentation line with another diamond. On the top, the diamond will be split in half or more along the direction of the texture with a suitable force on the split knife.
Saw cutting: Most diamonds are not suitable for splitting. At this time, you need to cut it with a saw. Because only diamonds can cut the diamond, the saw tablet is a diamond powder and lubricant coated on the edge Phosphorus and copper cyclone. Diamonds are fixed on the clip, and the diamond can be seen at a high speed to see the diamond. Modern laser technology introduces diamond cutting, which greatly improves the processing efficiency of drill billets
formed: Saw or split diamonds and then send them to the circle to play rounds and form. Common cut flowers such as circular, heart -shaped, oval, pointed, emerald, or other special shapes. Because diamonds are the hardest natural substances that humans have recognized so far, only diamonds can polish diamonds, and the hardness of the diamonds is slightly different. Only, the basic form of diamonds must be grasped with experience: trilogy, eight -facial body, duodang body and crystal characteristics. The general method is to rotate the drill blank high -speed lathe, and then use the diamond on the other arm to round the rotating drill billet.
Pliles, polishing: On a cast iron disc with diamond powder and lubricant, the car grinds all the petals (aspect) to make the diamond emit a seductive glory. The grinding process is usually to make 8 large faces at the bottom, and then make 16 face -to -face. Add a sharp bottom, a total of 25 aspects, the correct change is correct, and thus extend the triangular noodles, the kite face and waist face, a total of 33 aspects. Such a round diamonds have a total of 58 aspects. There are 57 face -to -face if there is no bottom face. Not every drill billet must go through all five processes. This depends on the characteristics of the drill billet and the goals to be achieved. Such as processing grandmother's green diamonds, there is no need to go through the "round" process. However, there are two processes for any diamond blank. This is "scratching" and "lobe, polishing". The petals produced by a precision -cut diamond, the location and angle of the position and angle are accurately calculated, making the diamond emit the maximum glory. In this, it can be seen that cutting the world's hardest gem -diamonds not only require advanced equipment, but also requires cutting artists from rich experience, high sense of responsibility and full attention to release all the spirit of diamonds. A diamond in the jewelry counter may be left through many countries. After several people, it becomes a diamond jewelry through processing, inlaid, and production.
Diamond cutting and grinding process: A diamond blank looks inconspicuous. It must be carefully cut and processed to become the flashing diamonds we are accustomed to. Therefore, the diamond car worker directly affects the value of diamonds. See the following description for details. The most ideal cutting effect is of course to maintain the maximum weight of the diamond, minimize the flaws as much as possible, and fully show the beauty of the diamond to make the diamond light. The general cutting process includes the following steps: mark (line): This is the first step of diamond cutting. First check the drilling blank and mark the surface of the diamond. technology. The ultimate goal is to create the largest, cleanest and most perfect diamonds to reflect the value of diamonds as high as possible. The threading staff must pay attention to two points: that is, try to maintain the maximum weight and minimize the internal content. The threadr uses a magnifying glass to study the structure of the drilling billet. If it is a large particle diamond, this work may take several months, and it takes several minutes to the ordinary drill billet. However, no matter how small the drilling billet is small, each diamond must be checked in detail to make the correct judgment. The threadr used Indian ink to mark on the drill billet, showing that the drill billet should be divided along this line. Usually, as much as possible along the natural texture direction of diamonds. Division of rough stones: including cutting and sawing cutting. Cutting: The splitter puts the diamond billet of the threaded thread on the suit, and then cuts a dentan along the segmentation line with another diamond, and then puts the square knife on the dental. On the knife, the diamond will be split into two or more pieces along the texture direction. Saw cutting: Most diamonds are not suitable for splitting. At this time, you need to cut it with a saw. Because only diamonds can cut diamonds, a saw tablet is a phosphorus and copper -bronze sheet with diamond powder and lubricants on the edge. Diamonds are fixed on the clip, and the diamond can be seen at a high speed to see the diamond. Modern laser technology introduces diamond cutting, which greatly improves the processing efficiency of drilling. Molding: The diamonds that are sawn or split are then sent to the circle to play round and formed, that is, the diamonds make diamonds in a round, heart -shaped, oval, pointed, emerald and other common cutting flowers according to design requirements. Or other special shapes. Because diamonds are the hardest natural substances that humans have recognized so far, only diamonds can polish diamonds, and the hardness of the diamonds is slightly different. Therefore, it is necessary to grasp the basic form of diamonds with experience when grinding: trilogy, eight -facial body, duodang body and crystal characteristics. The general method is to rotate the drill blank high -speed lathe, and then use the diamond on the other arm to round the rotating drill billet. Plourion and polishing: On a cast iron disc with diamond powder and lubricating oil, the car grinds all the petals (aspect) to make the diamond emit a seductive glory. The grinding process is usually to make 8 large noodles at the bottom, and then make 16 aspects. Add a sharp bottom, a total of 25 aspects, the correct change is correct, and thus extend the triangular noodles, the kite face and waist face, a total of 33 aspects. Such a round diamonds have a total of 58 aspects. There are 57 face -to -face if there is no bottom face. Not every drill billet must go through all five processes. This depends on the characteristics of the drill billet and the goals to be achieved. Such as processing grandmother's green diamonds, there is no need to go through the "round" process. However, there are two processes for any diamond blank. This is "scratching" and "lobe, polishing". The location and angle of the petal -cut diamond -cut diamonds are accurately calculated, making the diamond the maximum glory. It can be seen that cutting the world's hardest gem -diamonds not only require advanced equipment, but also need to cut the spirit of all diamonds from rich experience, high sense of responsibility, and full attention. A diamond in the jewelry counter may be left through many countries. After several people, it becomes a diamond jewelry through processing, inlaid, and production. With the advancement of science and technology, the introduction of laser technology and electronic computer descriptions can make the design and cutting of drilling blank more accurate. Reference materials: Golden Jewelry Network
The general cutting process includes the following steps:
labeled (threading): This is the first step of diamond cutting, first check the drill blank, and mark it on the surface of the diamond. Experience and proficient processing technology. The ultimate goal is to create the largest, cleanest and most perfect diamonds to reflect the value of diamonds as high as possible.
The thorough person must pay attention to two points: that is, try to maintain the maximum weight and minimize the internal content. The threadr uses a magnifying glass to study the structure of the drilling billet. If it is a large particle diamond, this work may take several months, and it takes several minutes to the ordinary drill billet.
, no matter how small the drilling billet is small, each diamond must be checked in detail to make the correct judgment.
This thoroughly marked with Indian ink on the drill billet, showing that the drill billet should be divided along this line. Usually, as much as possible along the natural texture direction of diamonds.
The segmentation rough: including cutting and sawing cutting.
This chopping: The splitter puts the diamond billet of the schemes on the suitcase, and then cuts a dentan along the segmentation line with another diamond. On the top, the diamond will be split in half or more along the direction of the texture with a suitable force on the split knife.
Saw cutting: Most diamonds are not suitable for splitting. At this time, you need to cut it with a saw. Because only diamonds can cut the diamond, the saw tablet is a diamond powder and lubricant coated on the edge Phosphorus and copper cyclone. Diamonds are fixed on the clip, and the diamond can be seen at a high speed to see the diamond. Modern laser technology introduces diamond cutting, which greatly improves the processing efficiency of drill billets
formed: Saw or split diamonds and then send them to the circle to play rounds and form. Common cut flowers such as circular, heart -shaped, oval, pointed, emerald, or other special shapes. Because diamonds are the hardest natural substances that humans have recognized so far, only diamonds can polish diamonds, and the hardness of the diamonds is slightly different.
Only, the basic form of diamonds must be grasped with experience: trilogy, eight -facial body, duodang body and crystal characteristics. The general method is to rotate the drill blank high -speed lathe, and then use the diamond on the other arm to round the rotating drill billet.
Pliles, polishing: On a cast iron disc with diamond powder and lubricant, the car grinds all the petals (aspect) to make the diamond emit a seductive glory.
The grinding process is usually to make 8 large faces at the bottom, and then make 16 face -to -face. Add a sharp bottom, a total of 25 aspects, the correct change is correct, and thus extend the triangular noodles, the kite face and waist face, a total of 33 aspects. Such a round diamonds have a total of 58 aspects. There are 57 face -to -face if there is no bottom face. Not every drill billet must go through all five processes. This depends on the characteristics of the drill billet and the goals to be achieved. Such as processing grandmother's green diamonds, there is no need to go through the "round" process. However, there are two processes for any diamond blank. This is "scratching" and "lobe, polishing".
The petals produced by a precision -cut diamond, the location and angle of the position and angle are accurately calculated, making the diamond emit the maximum glory.
In this, it can be seen that cutting the world's hardest gem -diamonds not only require advanced equipment, but also requires cutting artists from rich experience, high sense of responsibility and full attention to release all the spirit of diamonds. A diamond in the jewelry counter may be left through many countries. After several people, it becomes a diamond jewelry through processing, inlaid, and production.
Diamond cutting and grinding process: A diamond blank looks inconspicuous. It must be carefully cut and processed to become the flashing diamonds we are accustomed to. Therefore, the diamond car worker directly affects the value of diamonds. See the following description for details. The most ideal cutting effect is of course to maintain the maximum weight of the diamond, minimize the flaws as much as possible, and fully show the beauty of the diamond to make the diamond light. The general cutting process includes the following steps: mark (line): This is the first step of diamond cutting. First check the drilling blank and mark the surface of the diamond. technology. The ultimate goal is to create the largest, cleanest and most perfect diamonds to reflect the value of diamonds as high as possible. The threading staff must pay attention to two points: that is, try to maintain the maximum weight and minimize the internal content. The threadr uses a magnifying glass to study the structure of the drilling billet. If it is a large particle diamond, this work may take several months, and it takes several minutes to the ordinary drill billet. However, no matter how small the drilling billet is small, each diamond must be checked in detail to make the correct judgment. The threadr used Indian ink to mark on the drill billet, showing that the drill billet should be divided along this line. Usually, as much as possible along the natural texture direction of diamonds. Division of rough stones: including cutting and sawing cutting. Cutting: The splitter puts the diamond billet of the threaded thread on the suit, and then cuts a dentan along the segmentation line with another diamond, and then puts the square knife on the dental. On the knife, the diamond will be split into two or more pieces along the texture direction. Saw cutting: Most diamonds are not suitable for splitting. At this time, you need to cut it with a saw. Because only diamonds can cut diamonds, a saw tablet is a phosphorus and copper -bronze sheet with diamond powder and lubricants on the edge. Diamonds are fixed on the clip, and the diamond can be seen at a high speed to see the diamond. Modern laser technology introduces diamond cutting, which greatly improves the processing efficiency of drilling. Molding: The diamonds that are sawn or split are then sent to the circle to play round and formed, that is, the diamonds make diamonds in a round, heart -shaped, oval, pointed, emerald and other common cutting flowers according to design requirements. Or other special shapes. Because diamonds are the hardest natural substances that humans have recognized so far, only diamonds can polish diamonds, and the hardness of the diamonds is slightly different. Therefore, it is necessary to grasp the basic form of diamonds with experience when grinding: trilogy, eight -facial body, duodang body and crystal characteristics. The general method is to rotate the drill blank high -speed lathe, and then use the diamond on the other arm to round the rotating drill billet. Plourion and polishing: On a cast iron disc with diamond powder and lubricating oil, the car grinds all the petals (aspect) to make the diamond emit a seductive glory. The grinding process is usually to make 8 large noodles at the bottom, and then make 16 aspects. Add a sharp bottom, a total of 25 aspects, the correct change is correct, and thus extend the triangular noodles, the kite face and waist face, a total of 33 aspects. Such a round diamonds have a total of 58 aspects. There are 57 face -to -face if there is no bottom face. Not every drill billet must go through all five processes. This depends on the characteristics of the drill billet and the goals to be achieved. Such as processing grandmother's green diamonds, there is no need to go through the "round" process. However, there are two processes for any diamond blank. This is "scratching" and "lobe, polishing". The location and angle of the petal -cut diamond -cut diamonds are accurately calculated, making the diamond the maximum glory. It can be seen that cutting the world's hardest gem -diamonds not only require advanced equipment, but also need to cut the spirit of all diamonds from rich experience, high sense of responsibility, and full attention. A diamond in the jewelry counter may be left through many countries. After several people, it becomes a diamond jewelry through processing, inlaid, and production. With the advancement of science and technology, the introduction of laser technology and electronic computer descriptions can make the design and cutting of drilling blank more accurate. Reference materials: Golden Jewelry Network